|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
 |
|
|
|
|
|
INSTALLING
THE PRAZI BEAM CUTTER™
Model PR-7000
|
|
|
 |
|
|
|
BE
SURE SAW IS UNPLUGGED BEFORE INSTALLING BEAM CUTTER
X X |
|
|
|
|
|
REMOVE
BLADE |
|
|
|
|
|
|
|
|
|
 |
|
|
|
|
|
1 |
|
Open
foot plate to it's fully-extended position. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2 |
|
While
depressing lock button, remove blade bolt,
outer washer, blade and inner washer or diamond. |
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Due
to a design change on the Skil #77: New style type #17 or higher
requires a longer bushing.
DO NOT USE
the shorter bushing
(#P-7021),
Use of the incorrect bushing could cause damage to the bearing.
X |
|
|
INSTALL
BEAM CUTTER BLADE ASSEMBLY |
|
|
 |
|
|
|
3 |
|
Slip
Bushing in place. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
#P7021
for Craftsman®, Black & Decker®, DeWalt®
#P7022 for Milwaukee®
No bushing required for Makita® saws around spindle.
NOTE: Skil 77 type#17 or higher requires bushing #P7022. Older style Skil
requires bushing #P7021. |
|
|
|
|
|
|
|
|
4 |
|
With
foot plate fully extended, slide Beam Cutter blade - first
through the top of the table plate, then align the center hole
of the Beam Cutter with the saw spindle. |
|
|
|
|
 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
5 |
|
Drop
the Beam Cutter in place, making sure that the center hole
of the Beam Cutter aligns with the spindle of the saw. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
6 |
|
Loosen
the 2 screws on the Beam Cutter hinge with 5/32" hex wrench. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
7 |
|
Bolt
hinge on Beam Cutter to slide on saw and finger-tighten. Bolts,
washers and nuts are provided for this purpose. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
8 |
|
Screw
bolt, with washer on counterclockwise
(#P7023 for Black & Decker®, Milwaukee®, Craftsman® and
Skil®
#P7025 for Makita®)
through center hole in Beam Cutter. Make sure washer is on bolt - failing
to use the supplied washer may cause damage to the bearing. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
 |
|
|
|
|
|
|
9 |
|
At
this point, align Beam Cutter so that it is perpendicular (90°)
to the foot plate of the saw. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
TIGHTEN
BOLTS AND SCREWS |
|
|
|
|
|
|
|
|
|
|
10 |
|
With
blade aligned, and while depressing the lock button, tighten
the master nut with a 9/16' wrench. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
11 |
|
Tighten
the bolts holding the hinge to the slide with a 1/2" wrench. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
12 |
|
Tighten
screws on hinge assembly with a 5/32" hex wrench. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
NOTE |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
After
installing the Beam Cutter, please check to make sure that
there is enough tension on the chain. If more tension is desired,
loosen the tension screw and hinge bolts (#P7042) and push
the tension lever to achieve the desired tension level. Then
re-tighten the tension screw.
CLICK HERE FOR DETAILED TENSION ADJUSTMENT
INSTRUCTIONS |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
